YotaTech Forums
It has BEGUN!!!
It has BEGUN!!!
0 2017/08/29 15:06:58
Caliper is held on by 2 17mm bolts.
Caliper is held on by 2 17mm bolts.
0 2017/08/29 15:05:52
Test fit to see fi you have to trim the shield, I did, by about 2mm
Test fit to see fi you have to trim the shield, I did, by about 2mm
0 2017/08/29 15:05:29
Fancy parts
Fancy parts
0 2017/08/29 15:05:15
Stock parts
Stock parts
0 2017/08/29 15:05:04
Hard brake line is delicate. 10mm use a flare wrench
Hard brake line is delicate. 10mm use a flare wrench
0 2017/08/29 15:04:51
Dust shield trimmed
Dust shield trimmed
0 2017/08/29 15:04:39
It has BEGUN
It has BEGUN
0 2017/08/29 15:04:26
0 2017/08/29 14:46:56
0 2017/08/29 14:46:44
0 2017/08/29 14:46:31
The caliper comes off with 2 17mm bolts. Be careful taking it off so you don't bend and break the hard line coming off the back.
The caliper comes off with 2 17mm bolts. Be careful taking it off so you don't bend and break the hard line coming off the back.
0 2017/08/29 14:42:06
If you don't undo the brake line early in your swap, tie up the old caliper being careful with that hard line.
If you don't undo the brake line early in your swap, tie up the old caliper being careful with that hard line.
0 2017/08/29 14:41:48
Heh, there's something hiding back there. It's a whole bunch of WOAH!!!!
Heh, there's something hiding back there. It's a whole bunch of WOAH!!!!
0 2017/08/29 14:41:36
Test fit the rotor for interference with the dust shield. I had to trim it back about 2mm.
Test fit the rotor for interference with the dust shield. I had to trim it back about 2mm.
0 2017/08/29 14:41:22
Power slot cross-drilled and slotted directional rotors with rebuilt 231 13WL calipers
Power slot cross-drilled and slotted directional rotors with rebuilt 231 13WL calipers
0 2017/08/29 14:41:08
Stock brakes
Stock brakes
0 2017/08/29 14:40:53
This brake line is delicate. Use caution. It is a 10mm, use a flare wrench!!! Thank me later
This brake line is delicate. Use caution. It is a 10mm, use a flare wrench!!! Thank me later
0 2017/08/29 14:40:38
The dust shield has been trimmed.
The dust shield has been trimmed.
0 2017/08/29 14:40:26
It has BEGUN!!!
It has BEGUN!!!
0 2017/08/29 14:40:12
Check the new rotor for interference with the dust shield, I had to trim the inside of the dust shield about 2 mm.
Check the new rotor for interference with the dust shield, I had to trim the inside of the dust shield about 2 mm.
0 2017/08/29 14:36:35
You can disconnect the brake line or tie up the caliper until you are ready to deal with it.
You can disconnect the brake line or tie up the caliper until you are ready to deal with it.
0 2017/08/29 14:35:40
Here is the delicate hard brake line. There is a clip that holds it in place near the ABS line. It is a 10mm, use a flare wrench!!!
Here is the delicate hard brake line. There is a clip that holds it in place near the ABS line. It is a 10mm, use a flare wrench!!!
0 2017/08/29 14:34:33
There are 2 17mm bolts that hold the caliper to the spindle. Remove those and be careful that the caliper doesn't hang from the brake line.
There are 2 17mm bolts that hold the caliper to the spindle. Remove those and be careful that the caliper doesn't hang from the brake line.
0 2017/08/29 14:33:33
The old
The old
0 2017/08/29 14:32:57
It has BEGUN!!!!
It has BEGUN!!!!
0 2017/08/29 14:32:20
Like nothing happened
Like nothing happened
0 2017/08/16 11:39:41
All the plastic has to come off
All the plastic has to come off
0 2017/08/16 11:39:29
Module close-up
Module close-up
0 2017/08/15 13:10:00
'97 roof w/ module
'97 roof w/ module
0 2017/08/15 13:09:59
'99 roof w/o module
'99 roof w/o module
0 2017/08/15 13:09:58
You can barely notice the remains of the chip. At this point it is no different than a small drop of rain.
You can barely notice the remains of the chip. At this point it is no different than a small drop of rain.
0 2017/04/06 12:58:59
Then the spoiler is attached to the pylons. (I probably should have painted it before I installed it. Oh well, it isn't hard to take off.)
Then the spoiler is attached to the pylons. (I probably should have painted it before I installed it. Oh well, it isn't hard to take off.)
0 2017/04/06 09:56:58
The mounting brackets are attached with nut-serts. 3 per side.
The mounting brackets are attached with nut-serts. 3 per side.
0 2017/04/06 09:56:09
0 2016/09/06 10:40:50
99 4Runner airbox
99 4Runner airbox
0 2016/09/06 10:24:40