YotaTech Forums
Filling the bottle with beads, 6 ounces do NOT fit in the bottle at once
Filling the bottle with beads, 6 ounces do NOT fit in the bottle at once
0 2018/03/19 11:15:16
Beads clogging the tube
Beads clogging the tube
0 2018/03/19 11:15:15
Remove the stock valve core and drain the air.
Remove the stock valve core and drain the air.
0 2018/03/19 11:10:57
Standard valve core on left, filter core on right.
Standard valve core on left, filter core on right.
0 2018/03/19 11:10:57
The kit came with a filling bottle and 5 bags pre-measured to 6 ounces.
The kit came with a filling bottle and 5 bags pre-measured to 6 ounces.
0 2018/03/19 11:10:56
The kit came with a very nice metal valve core removal tool.
The kit came with a very nice metal valve core removal tool.
0 2018/03/19 11:10:55
Pour beads from bottle into tire with included tube.
Pour beads from bottle into tire with included tube.
0 2018/03/19 11:10:54
Adding beads to the fill bottle, 6 ounces do NOT fit in the bottle at 1 time.
Adding beads to the fill bottle, 6 ounces do NOT fit in the bottle at 1 time.
0 2018/03/19 11:10:53
Fill slowly or the tube will clog
Fill slowly or the tube will clog
0 2018/03/19 11:10:52
Other 4 rims and an extra I had in the garage
Other 4 rims and an extra I had in the garage
0 2018/03/19 11:00:27
Spare rim
Spare rim
0 2018/03/19 10:59:21
0 2017/12/11 07:08:03
0 2017/12/11 07:07:57
I drained the pan first. This was a lot worse than I thought. It's basically black.
I drained the pan first. This was a lot worse than I thought. It's basically black.
0 2017/11/28 11:46:08
Fresh ATF
Fresh ATF
0 2017/11/28 11:46:06
The final purge.
The final purge.
0 2017/11/28 11:46:03
This is the final purge of fluid. Still a little dark, but it is nearly red when poured against something.
This is the final purge of fluid. Still a little dark, but it is nearly red when poured against something.
0 2017/11/28 11:46:01
Dirty Smear of fluid to begin. At every fuel fill-up I would check my fluids and this never had a burnt smell, but has been slowly getting darker.
Dirty Smear of fluid to begin. At every fuel fill-up I would check my fluids and this never had a burnt smell, but has been slowly getting darker.
0 2017/11/28 11:45:58
Clean Smear of fluid after the flush
Clean Smear of fluid after the flush
0 2017/11/28 11:45:55
Here is the filter on the return line from the rack to the reservoir
Here is the filter on the return line from the rack to the reservoir
0 2017/11/28 11:42:30
It is packed full of the yellow grease seen here on the motor drive wheel.
It is packed full of the yellow grease seen here on the motor drive wheel.
0 2017/11/28 07:39:56
This is the cap with the contact traces. There was a dried and caked yellow grease and green tarnish on the contacts
This is the cap with the contact traces. There was a dried and caked yellow grease and green tarnish on the contacts
0 2017/11/28 07:39:55
Here is the inside of a new and clean actuator
Here is the inside of a new and clean actuator
0 2017/11/28 07:39:53
These 3 contact pins ride along contact tracks in the cap which determine limit for shifting 2wd -> 4wd. These tabs were coated in a green tarnish.
These 3 contact pins ride along contact tracks in the cap which determine limit for shifting 2wd -> 4wd. These tabs were coated in a green tarnish.
0 2017/11/28 07:39:52
0 2017/11/22 14:31:21
0 2017/11/22 14:30:47
0 2017/11/08 14:19:50
0 2017/11/08 14:18:23
0 2017/11/01 14:37:51
0 2017/09/30 09:10:07
There's a whole lot of WOAH hiding back there.
There's a whole lot of WOAH hiding back there.
0 2017/08/29 15:15:57
0 2017/08/29 15:11:37
0 2017/08/29 15:11:28
0 2017/08/29 15:11:18
The caliper is held on by 2 17mm bolts and a small hard brake line. Be careful!!!
The caliper is held on by 2 17mm bolts and a small hard brake line. Be careful!!!
0 2017/08/29 15:08:08
Test fit the rotor to see if dust cover clearance is an issue.
Test fit the rotor to see if dust cover clearance is an issue.
0 2017/08/29 15:07:55
New shiny parts. I look forward to a long relationship.
New shiny parts. I look forward to a long relationship.
0 2017/08/29 15:07:44
Old parts. Thank you for your service.
Old parts. Thank you for your service.
0 2017/08/29 15:07:32
Hard brake line. it's delicate and takes a 10mm. Use a flare wrench!!!
Hard brake line. it's delicate and takes a 10mm. Use a flare wrench!!!
0 2017/08/29 15:07:20
Trimmed dust shield. You have to cut the top and the bottom for caliper clearance, and possibly the inner edge for rotor clearance
Trimmed dust shield. You have to cut the top and the bottom for caliper clearance, and possibly the inner edge for rotor clearance
0 2017/08/29 15:07:11