Window weatherflectors etc
#1
Registered User
Thread Starter
Join Date: Dec 2003
Location: Redwoods of Norcal and SE Alaska
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Window weatherflectors etc
Contemplating rain guards for the windows. Two methods of intallation:
1) Tape
2) Groove wedge
Pros and cons #1 vs #2? Appearance? Failure? Other?
Thanks
1) Tape
2) Groove wedge
Pros and cons #1 vs #2? Appearance? Failure? Other?
Thanks
#4
Registered User
The PO of my 99 had installed "Ventshade" brand shades over front and back windows and they're the type that stick on the outside. I haven't had any problem with them, and the truck has seen heat as high as 100+ and as low as -15 and speeds of up to the speed limiter without any losses of any kind. I had the kind that fit inside the window track at the top of the track where the window meets the frame in an explorer I had a while back, and I was content with them as well. If you clean the surface well and follow instructions, I'd expect either kind to last a few years at least.
Trending Topics
#12
Contributing Member
Join Date: May 2003
Location: Piedmont, North Carolina
Posts: 827
Likes: 0
Received 0 Likes
on
0 Posts
I went with #2. WeatherTech
There is glue even though they say channel. It glues to the inside of the channel(BW). Held up well for four months. NEVER could get the auto driver window to accept the visor. Constant game of whack-a-mole. Up, down, Up, down! Took much advice from fellow YotaTech members. And the damn plexi plastic is so brittle, you'll do a contortionist act getting it bent enough to fit in the channel. Pressure holds it in place. I put a big scratch down the side of my mirror trying to bulldog that thing into the groove.
Got cold and rainy. At the post office I rolled down my window to drop a letter and the guard followed the window down and fell out and off. Before I could jump out and grap it, embarresed as hell, another car drove over it. I went home took the others out, extremely easy, too easy obviously, and pitched them in the dumpster. My story. :pat:
notice my sig??
There is glue even though they say channel. It glues to the inside of the channel(BW). Held up well for four months. NEVER could get the auto driver window to accept the visor. Constant game of whack-a-mole. Up, down, Up, down! Took much advice from fellow YotaTech members. And the damn plexi plastic is so brittle, you'll do a contortionist act getting it bent enough to fit in the channel. Pressure holds it in place. I put a big scratch down the side of my mirror trying to bulldog that thing into the groove.
Got cold and rainy. At the post office I rolled down my window to drop a letter and the guard followed the window down and fell out and off. Before I could jump out and grap it, embarresed as hell, another car drove over it. I went home took the others out, extremely easy, too easy obviously, and pitched them in the dumpster. My story. :pat:
notice my sig??
Last edited by Sac State; 01-12-2004 at 02:03 PM.
#13
Registered User
Join Date: Apr 2003
Location: Arizona
Posts: 1,009
Likes: 0
Received 0 Likes
on
0 Posts
Has anyone tried Performance Products rain guards? I'm thinking of getting them, but I'm not too sure on how well they will hold up...
http://www.performanceproducts.com/P...producttype=20
Thanks,
-- Andrey
http://www.performanceproducts.com/P...producttype=20
Thanks,
-- Andrey
#14
No glue
Originally posted by Sac State
I went with #2. WeatherTech
There is glue even though they say channel. It glues to the inside of the channel(BW). Held up well for four months. NEVER could get the auto driver window to accept the visor. Constant game of whack-a-mole. Up, down, Up, down! Took much advice from fellow YotaTech members. And the damn plexi plastic is so brittle, you'll do a contortionist act getting it bent enough to fit in the channel. Pressure holds it in place. I put a big scratch down the side of my mirror trying to bulldog that thing into the groove.
Got cold and rainy. At the post office I rolled down my window to drop a letter and the guard followed the window down and fell out and off. Before I could jump out and grap it, embarresed as hell, another car drove over it. I went home took the others out, extremely easy, too easy obviously, and pitched them in the dumpster. My story. :pat:
notice my sig??
I went with #2. WeatherTech
There is glue even though they say channel. It glues to the inside of the channel(BW). Held up well for four months. NEVER could get the auto driver window to accept the visor. Constant game of whack-a-mole. Up, down, Up, down! Took much advice from fellow YotaTech members. And the damn plexi plastic is so brittle, you'll do a contortionist act getting it bent enough to fit in the channel. Pressure holds it in place. I put a big scratch down the side of my mirror trying to bulldog that thing into the groove.
Got cold and rainy. At the post office I rolled down my window to drop a letter and the guard followed the window down and fell out and off. Before I could jump out and grap it, embarresed as hell, another car drove over it. I went home took the others out, extremely easy, too easy obviously, and pitched them in the dumpster. My story. :pat:
notice my sig??
Perhaps glue on the 4th genners, but not for my 3rd, it it completely in channel, with NO GLUE.
#16
Contributing Member
Join Date: Sep 2003
Location: Central Virginia (BFE)
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
EGR
I got the EGR slimline. They are very well made as many of you are familar with thier supergaurd. Nice match. They come in both in-channel and "sticky" type. I went with the tape because I had tape on my 92' pickup for 5+ years without a problem (strong as ever). I coundn't imagine a snap in not shaking or rattling at high speeds and not interfering with the window. I think the tape style gives a cleaner exterior look anyhow. My 2 Cents
#17
Contributing Member
Join Date: May 2003
Location: Piedmont, North Carolina
Posts: 827
Likes: 0
Received 0 Likes
on
0 Posts
'It glues to the inside of the channel(BW).'
BW=back door windows. There was a strip of glue along the ridge of the visors for the back windows. The glue is supposed to stick to the inside of the channel, or so it said in the instructions. Front visors were the wrestle in kind, no tape.
BW=back door windows. There was a strip of glue along the ridge of the visors for the back windows. The glue is supposed to stick to the inside of the channel, or so it said in the instructions. Front visors were the wrestle in kind, no tape.
#18
Registered User
Join Date: Nov 2002
Location: San Diego
Posts: 927
Likes: 0
Received 0 Likes
on
0 Posts
What about offroading? Do these get scratches (pinstriping) or do they get pulled off? I'm leaning more towards the no tape kind so I can remove them when I go offroad. Anybody have any experience with that?
#19
Registered User
i went with the weatherflectors mainly b/c it looked better. for those of you who are curious about the front window install, here's my writeup on that:
http://4runners.org/articles/macneil/index.html
it just requires careful bending thats all.
bob
http://4runners.org/articles/macneil/index.html
it just requires careful bending thats all.
bob
#20
Registered User
Originally posted by RobT2k
What about offroading? Do these get scratches (pinstriping) or do they get pulled off? I'm leaning more towards the no tape kind so I can remove them when I go offroad. Anybody have any experience with that?
What about offroading? Do these get scratches (pinstriping) or do they get pulled off? I'm leaning more towards the no tape kind so I can remove them when I go offroad. Anybody have any experience with that?