How many of you are considering the IFS locker?
#1
Contributing Member
Thread Starter
Join Date: Jul 2002
Location: Colorado
Posts: 2,657
Likes: 0
Received 0 Likes
on
0 Posts
How many of you are considering the IFS locker?
Hey all-
I just e-mail Off Road Solutions to find out how much it would cost to have the ARB front diff locker and manual hub conversion installed.
Just wondering how many of you are thinking about the front locker, too?
I just e-mail Off Road Solutions to find out how much it would cost to have the ARB front diff locker and manual hub conversion installed.
Just wondering how many of you are thinking about the front locker, too?
#2
Registered User
Join Date: Dec 2002
Location: Deep Gap, NC
Posts: 4,697
Likes: 0
Received 0 Likes
on
0 Posts
I'm going to get one, but it's going to be a a little while. I'm going to get one for the rear too. Any news on the fuel atomizer and heat exchanger writeups yet?
Chris
Chris
#4
Contributing Member
Join Date: Jan 2003
Location: Houston, TX
Posts: 5,377
Likes: 0
Received 0 Likes
on
0 Posts
I'll be doing the manual hub conversion myself this summer sometime, hopefully. then later in the fall I'll spring for the front and rear arb lockers and install them. gotta space it out because of the cost.
#5
Contributing Member
Join Date: May 2002
Location: Atlanta, GA
Posts: 2,068
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by keisur
I'll be doing the manual hub conversion myself this summer sometime, hopefully. then later in the fall I'll spring for the front and rear arb lockers and install them. gotta space it out because of the cost.
I'll be doing the manual hub conversion myself this summer sometime, hopefully. then later in the fall I'll spring for the front and rear arb lockers and install them. gotta space it out because of the cost.
#6
Contributing Member
Thread Starter
Join Date: Jul 2002
Location: Colorado
Posts: 2,657
Likes: 0
Received 0 Likes
on
0 Posts
That's why I called ORS. I figured labor might be a little less on the ARB install because the axles have to be removed anyway. And since the axles are going to be removed, why not replace them with the manual hubs?
[Homer voice]Mmmm...front and rear lockers[Homer voice]
Gettin' really excited for spring and summer to get here. The Slaughterhouse run was just a tease. I want to 4 wheel more!
[Homer voice]Mmmm...front and rear lockers[Homer voice]
Gettin' really excited for spring and summer to get here. The Slaughterhouse run was just a tease. I want to 4 wheel more!
Last edited by HaveBlue; 03-03-2003 at 06:45 AM.
#7
Registered User
Join Date: Jan 2003
Location: Waynesboro, VA
Posts: 141
Likes: 0
Received 0 Likes
on
0 Posts
Hey haveblue,
Haveblue,
All other names taken so is pulling your leg.
The manual hub conversion takes all of 15 min per side and you could almost teach my dog how to do it.
It will work better with the axles on the vehicle that way you can lock it in 4wd to stop the half shafts from spinning as you losen or tighten the center bolt.
Find a junk/salvage yard and pick the hubs up and then look for the writeups on this board. Or just use a hayes or chiltons.
9-10 hubs in the junkyard if not taken off work like new. Of course the hubs I got from the yard one doesnt work that smooth because someone had jerked it off and hit the dial in the center with the hammer. Problebly impatient. It was sitting covered in a rag on the driver seat.
Brass drift is a must just so you dont damage the studs. If you are pulling them of the donor truck tap the studs slightly towards the center and the cone washers come our pretty easy.
Lockers might be in order for my 1995 in about 5 years, gotta budget for them. Plus my wife will have something else to drive by then.
Mike
All other names taken so is pulling your leg.
The manual hub conversion takes all of 15 min per side and you could almost teach my dog how to do it.
It will work better with the axles on the vehicle that way you can lock it in 4wd to stop the half shafts from spinning as you losen or tighten the center bolt.
Find a junk/salvage yard and pick the hubs up and then look for the writeups on this board. Or just use a hayes or chiltons.
9-10 hubs in the junkyard if not taken off work like new. Of course the hubs I got from the yard one doesnt work that smooth because someone had jerked it off and hit the dial in the center with the hammer. Problebly impatient. It was sitting covered in a rag on the driver seat.
Brass drift is a must just so you dont damage the studs. If you are pulling them of the donor truck tap the studs slightly towards the center and the cone washers come our pretty easy.
Lockers might be in order for my 1995 in about 5 years, gotta budget for them. Plus my wife will have something else to drive by then.
Mike
Trending Topics
#8
Registered User
Re: Hey haveblue,
All other names taken so is pulling your leg.
The manual hub conversion takes all of 15 min per side and you could almost teach my dog how to do it.
You have a darn smart dog!
Ryan is right on the money.
I am thinking about a front locker, mostly I am thinking that I wish I could figure out which fuse blew so mine would work again.
The manual hub conversion takes all of 15 min per side and you could almost teach my dog how to do it.
You have a darn smart dog!
Ryan is right on the money.
I am thinking about a front locker, mostly I am thinking that I wish I could figure out which fuse blew so mine would work again.
#10
Registered User
Join Date: May 2002
Location: Southern MD USA
Posts: 1,539
Likes: 0
Received 0 Likes
on
0 Posts
My ARB front locker is sitting right in front of me on my desk. As soon as the weather breaks and I am sure we are done with snow in my area, I am going to yank out that front diff and get busy!
Gadget
www.GadgetOnline.com
Gadget
www.GadgetOnline.com
#12
Contributing Member
Join Date: May 2002
Location: Atlanta, GA
Posts: 2,068
Likes: 0
Received 0 Likes
on
0 Posts
Re: Hey haveblue,
Originally posted by Hokiez97
Haveblue,
All other names taken so is pulling your leg.
The manual hub conversion takes all of 15 min per side and you could almost teach my dog how to do it.
Find a junk/salvage yard and pick the hubs up and then look for the writeups on this board. Or just use a hayes or chiltons.
Mike
Haveblue,
All other names taken so is pulling your leg.
The manual hub conversion takes all of 15 min per side and you could almost teach my dog how to do it.
Find a junk/salvage yard and pick the hubs up and then look for the writeups on this board. Or just use a hayes or chiltons.
Mike
if so, dont you think everyone would do that? the kit alone is close to $1000, plus all the labor as this is not a garage job.
#13
I think you're thinking of off road solutions kit. He's just talking about the manual hubs, not the cv joints, axle shafts and all of that stuff. I'd like to do the arb, but I don't have the money. It's great for people that want the ride of ifs and don't need the articulation of a solid axle.
#14
Contributing Member
Thread Starter
Join Date: Jul 2002
Location: Colorado
Posts: 2,657
Likes: 0
Received 0 Likes
on
0 Posts
Off Road Solutions is the only company offering the manual hub conversion for the 3rd gens.
Not to sound like a jerk, but I was actually talking about the ORS kit which is quite labor intensive.
Not to sound like a jerk, but I was actually talking about the ORS kit which is quite labor intensive.
#15
Contributing Member
Join Date: May 2002
Location: Atlanta, GA
Posts: 2,068
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by oly884
I think you're thinking of off road solutions kit. He's just talking about the manual hubs, not the cv joints, axle shafts and all of that stuff. I'd like to do the arb, but I don't have the money. It's great for people that want the ride of ifs and don't need the articulation of a solid axle.
I think you're thinking of off road solutions kit. He's just talking about the manual hubs, not the cv joints, axle shafts and all of that stuff. I'd like to do the arb, but I don't have the money. It's great for people that want the ride of ifs and don't need the articulation of a solid axle.
#16
Registered User
The process Hokie is describing is that of an 86-95 runner, not a 3rd gen. Find me a yard that has a bunch of 3rd gen hubs sitting around.
RT is right, period.
Gadget, are you adding hubs too? I have not seen any pics of the new wheeler since the tire talk.
RT is right, period.
Gadget, are you adding hubs too? I have not seen any pics of the new wheeler since the tire talk.
#17
Registered User
Originally posted by Flygtenstein
The process Hokie is describing is that of an 86-95 runner, not a 3rd gen. Find me a yard that has a bunch of 3rd gen hubs sitting around.
The process Hokie is describing is that of an 86-95 runner, not a 3rd gen. Find me a yard that has a bunch of 3rd gen hubs sitting around.
I have a 2nd Gen, so I'm just stirring the pot...
#18
Registered User
BTW, I plan to do the ARB in the IFS. I'm going to make a run of using the IFS for a while (a SAS is a few years out likely).
I've seen (for the rear) complete 3rds setup with the ARB in it for $1500 or so. Since I'm not regearing, would I be better off just having the locker installed locally (if I can find a reputable shop!?!?!). If I got the complete 3rd is there any special equipment needed to swap it in myself?
I've seen (for the rear) complete 3rds setup with the ARB in it for $1500 or so. Since I'm not regearing, would I be better off just having the locker installed locally (if I can find a reputable shop!?!?!). If I got the complete 3rd is there any special equipment needed to swap it in myself?
#19
Contributing Member
Join Date: Jan 2003
Location: Houston, TX
Posts: 5,377
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by AllOtherNamesTakenSo
you realize how hard the install for manual hubs is? :pat:
you realize how hard the install for manual hubs is? :pat:
#20
Contributing Member
Join Date: Jan 2003
Location: Houston, TX
Posts: 5,377
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by HaveBlue
That's why I called ORS. I figured labor might be a little less on the ARB install because the axles have to be removed anyway. And since the axles are going to be removed, why not replace them with the manual hubs?
That's why I called ORS. I figured labor might be a little less on the ARB install because the axles have to be removed anyway. And since the axles are going to be removed, why not replace them with the manual hubs?