ToyoTech559's 1988 4Runner Build-Up Thread
#421
thanks. i know the newer ones have cardboard in them since one of the techs has cut one open. im pretty sure the older stuff has the same stuff in it as well. this weekend will work. could you text me the price. thanks again
#423
hahah ok.
well since i installed my elocker. after a few days i noticed a small leak. must be a combinations of stuff but i know for sure i used toyota black FIPG instead of the red. i have tons of black, used for resealing anything that has oil. red is for anything like transmission and/or sealing of stuff that uses gear oil. i got lazy and just went under the truck and tighten up the nuts and worked for a while but started to leak again. i noticed it was coming near the upper longer stud area. i went to tighten the nut on it and it started to pull the stud.
i ended up doing this at home (never again) back still sore... i dropped the third and found a stripped hole for the upper longer stud. i re tapped it and went to hardware store for a 5inch bolt. goal was to install the bolt from inside the diff but there wasnt enough room so i cut the head off and added threads since it wasnt a fully thread bolt. this allow me to install the home made custom stud further into the hole and i used a locking washer and nut on the inside of the stud to keep the stud from being pulled out. its much stronger now.
1st time i didnt use any gaskets, just black FIPG. this time i put some red FIPG on the rear diff housing than installed the factory paper gasket than applied some more red FIPG on top of that so the paper gasket is sandwiched in red FIPG. now the back killer, trying to man handled an odd 80lb 3rd member into the two long studs that was never perfectly straight to began with. sweating and cursing since i was racing against the drying FIPG. i finally got in on and bolted. just need to pick up the driveline tomorrow and get some gear oil. hope it doesnt leak and i fix the driveline noise..
oh and i giving it 2days for it to dry
well since i installed my elocker. after a few days i noticed a small leak. must be a combinations of stuff but i know for sure i used toyota black FIPG instead of the red. i have tons of black, used for resealing anything that has oil. red is for anything like transmission and/or sealing of stuff that uses gear oil. i got lazy and just went under the truck and tighten up the nuts and worked for a while but started to leak again. i noticed it was coming near the upper longer stud area. i went to tighten the nut on it and it started to pull the stud.
i ended up doing this at home (never again) back still sore... i dropped the third and found a stripped hole for the upper longer stud. i re tapped it and went to hardware store for a 5inch bolt. goal was to install the bolt from inside the diff but there wasnt enough room so i cut the head off and added threads since it wasnt a fully thread bolt. this allow me to install the home made custom stud further into the hole and i used a locking washer and nut on the inside of the stud to keep the stud from being pulled out. its much stronger now.
1st time i didnt use any gaskets, just black FIPG. this time i put some red FIPG on the rear diff housing than installed the factory paper gasket than applied some more red FIPG on top of that so the paper gasket is sandwiched in red FIPG. now the back killer, trying to man handled an odd 80lb 3rd member into the two long studs that was never perfectly straight to began with. sweating and cursing since i was racing against the drying FIPG. i finally got in on and bolted. just need to pick up the driveline tomorrow and get some gear oil. hope it doesnt leak and i fix the driveline noise..
oh and i giving it 2days for it to dry
Last edited by ToyoTech559; 04-20-2012 at 06:51 PM.
#429
not sure of any up coming Toyota events at pismo but i do plan on going in a month or two with a few friends
#433
Registered User
iTrader: (1)
been a busy weekend for me i guess. finally got around to adding a factory 4.88 IFS diff in. used my non add tube. i have to say those that do this on the ground must have more skills than i do. i did this on a lift and still was alot of work...
4runner to pre-runner
top is ADD 4.88 diff. just have to remove the stubby gear thing. i had to pop the cover open to pop the stub out
once the stub is out. you can see it looks just like a non add diff. just need to install a seal.
the seal on non add diff are the same on both sides
installed and you can see the ADD sticker and a NON ADD tube
not sure when these bad boys will be installed. just went with HREW kickout from 4x
4runner to pre-runner
top is ADD 4.88 diff. just have to remove the stubby gear thing. i had to pop the cover open to pop the stub out
once the stub is out. you can see it looks just like a non add diff. just need to install a seal.
the seal on non add diff are the same on both sides
installed and you can see the ADD sticker and a NON ADD tube
not sure when these bad boys will be installed. just went with HREW kickout from 4x
what do you call that seal. can i get one at napa or some place llike that or use the one off my current non add diff if it come out easily?
#434
IFS 7.5" front 3rd axle seals part # 90311-35032
i would get two and do both while you have it apart. i would also use oem since i have read others havent had good luck finding a non oem one that fit right
#435
so i swapped the ends and ujoints of my original drive shaft and installed them on to the other one i got from adam. got it all installed and guess what. same thing. from what i was able to see while it was up in the air. it look like the drive shaft is not balanced. so im gonna get it balanced and see what happens. i dont know how this even started or what caused it.. oh well. going on another trip to bald tomorrow. wont be much snow but i need a break lol
#436
Registered User
Join Date: Jun 2009
Location: Fresno, Ca
Posts: 719
Likes: 0
Received 0 Likes
on
0 Posts
That sucks to hear hope everything work out.
Are you going to bald with the big yota family? Might be some more snow cause the of light rain we had. Not too sure tough
Are you going to bald with the big yota family? Might be some more snow cause the of light rain we had. Not too sure tough