8T8 4RUNNER's 1988 4Runner Build-Up Thread
05-23-2011, 07:57 PM
#902
Haha... Yeah, I don't get yelled at, ...but, GEEESH, ....as clean as I had that thing, remember? SO MUCH CRAP leaking for 4500 miles, ....QUICKLY created a whole new realm of grease! lol. Ehhhhh, I actually also did the diff stuff, so that stuff hadn't been touched in a 1/4 million miles...but DANG, .....I can't wait till it's over! hahahaha.
Can't wait for more, Jerry, Joe! Bring it!!!! lol.
Can't wait for more, Jerry, Joe! Bring it!!!! lol.
05-24-2011, 02:39 AM
#903
YotaTech Milestone-Two Millionth Post
working waaaaaay too much this week.....so not sure when we will touch this again. "supposed" to be off thursday, so we will see.
05-25-2011, 01:42 AM
#907
YotaTech Milestone-Two Millionth Post
that's Ok....just a little bummed that I am working too much right now. frustrated to say the least that we make some good gains and then it comes to an abrupt halt.
05-27-2011, 07:44 PM
#908
Registered User
Join Date: Feb 2008
Location: Dallas
Posts: 155
Likes: 0
Received 0 Likes
on
0 Posts
Haven't been on in awhile and I just got all caught up again. It's looking awfully nice. I thought my heads were dirty, but they were nothing like yours! Those were a mess, nice cleaning job though.
So you gonna paint the oil filter too? That blue just doesn't work with everything else... j/k
Keep up the good work, I'm enjoying your build.
So you gonna paint the oil filter too? That blue just doesn't work with everything else... j/k
Keep up the good work, I'm enjoying your build.
05-28-2011, 02:22 AM
#910
YotaTech Milestone-Two Millionth Post
hey guys.....ummm, no , on the oil filter.....actually that one is a dud anyway......had taken off the fram with a stabbed screwdriver and threw that one on there to keep crud out of the area, so that one was never actually used.
"supposedly" off until tuesday....unless work calls (crosses fingers).....as 2nd in command, I am required to cover if nobody else can....but, for my sake, I already covered 16 extra hours this week....so hopefully it keeps anyone from looking cross-eyed at me because I already did my part.
anyway.
definitely going to make some progress....need to finish the valves o the passenger's side head....install it and start on the driver's side head.
"supposedly" off until tuesday....unless work calls (crosses fingers).....as 2nd in command, I am required to cover if nobody else can....but, for my sake, I already covered 16 extra hours this week....so hopefully it keeps anyone from looking cross-eyed at me because I already did my part.
anyway.
definitely going to make some progress....need to finish the valves o the passenger's side head....install it and start on the driver's side head.
lol. Sorry to hear about the 92, Jerry! You'll get it, QUICK LIKE!
05-28-2011, 01:18 PM
#912
Super Moderator
Staff
iTrader: (1)
Join Date: Aug 2008
Location: Anderson Missouri
Posts: 11,788
Likes: 0
Received 25 Likes
on
22 Posts
Doing my part to keep you from working this weekend. Hope you have some great family time and if your plans or for the 8T8 all goes well.
I must have missed something on the 92, guessing it is the oil filter. Hope all is well.
I must have missed something on the 92, guessing it is the oil filter. Hope all is well.
05-29-2011, 06:11 AM
#913
YotaTech Milestone-Two Millionth Post
did NOT have to work last night....they tried.....Lord knows, they tried. Wife all p-o'd because they called 3 times in an hour last night to have me figure crap out. Hopefully they leave me alone today....have a cookout to go to this afternoon. wife is working sat-sun-mon and I am off the same days....kinda much better for many reasons when that happens (married guys will understand that...and unmarried too)
my truck is fine and back on the road after getting towed home (see my thread...the "original" one) after breaking a coolant hose near the thermostat....temp fix done and will have to order that hose for $32...ouch.
garage cleaned this morning ...amazing how it gets so screwed up so fast.
did some detail stuff to Joe's motor...namely, chased the head bolt holes with an oiled bolt by hand twice each and the cleaned the block again and again until I was satisfied. new knock sensor wire installed as well.
waiting for Joe to get his butt in motion so we can finish the valves on the head and get that head on.
pics....of course.
new wire
driver's side of the block cleaned up
this says it all
05-29-2011, 08:40 AM
#915
YotaTech Milestone-Two Millionth Post
disregard...
boss called me about an hour ago and said "you are not on-call, they are not to be calling you, you are off, enjoy your time off, have 15 beers"......now that's a phone call I like.
boss called me about an hour ago and said "you are not on-call, they are not to be calling you, you are off, enjoy your time off, have 15 beers"......now that's a phone call I like.
05-29-2011, 09:01 AM
#916
Registered User
haha BOSS FTW.....
Not sure if it's just the photo or just me, but I am not quite sure I like that block surface for the head.
Not sure if it's just the photo or just me, but I am not quite sure I like that block surface for the head.
Last edited by xxxtreme22r; 05-29-2011 at 09:02 AM.
05-29-2011, 12:16 PM
#918
YotaTech Milestone-Two Millionth Post
05-29-2011, 12:22 PM
#919
YotaTech Milestone-Two Millionth Post
Ok....driver's side head is on and tightened down.
and blah-blah-blah.....on to the pics
all valves in
gasket on
after torquing to 33 ft/lbs after several passes to get to that, painted lines to point to 12 o'clock on the head bolts (by the way the ones from LCE are 12mm heads rather than 14mm heads)
then, in sequence, turned each enough to point to the 3 o'clock position
then, one more pass, to make them point to 6 o'clock
and here we area....cam is still out.....want to get the other head on before messing with FIPG and all that
after this, I cut grass for a few hours.....sitting now, waiting to go to a cookout
and blah-blah-blah.....on to the pics
all valves in
gasket on
after torquing to 33 ft/lbs after several passes to get to that, painted lines to point to 12 o'clock on the head bolts (by the way the ones from LCE are 12mm heads rather than 14mm heads)
then, in sequence, turned each enough to point to the 3 o'clock position
then, one more pass, to make them point to 6 o'clock
and here we area....cam is still out.....want to get the other head on before messing with FIPG and all that
after this, I cut grass for a few hours.....sitting now, waiting to go to a cookout
Last edited by 92 TOY; 05-29-2011 at 12:23 PM.
