I have recently wrapped up the restoration on my 1983 Toyota Pickup so it is garage sale time. In case you have not followed my build thread, I'm the kind of guy that likes to have nice new shiny parts on my truck so I have a lot of left over parts that are perfectly good and functional but don't quite up to my appearance standards. There are also several parts that I simply didn't need any more after upgrades. I WILL NOT SELL YOU WORTHLESS JUNK - All parts were functioning properly when removed, but most are just simply dirty and could be easily cleaned up with some degreaser and elbow grease, maybe a little paint. Any damaged parts will be disclosed in the descriptions below. Most parts are for a 1983 4WD Pickup, but I have also listed other years that I believe are compatible - the buyer will be responsible for confirming fitment. I know first hand how rare and unavailable some of these parts are so I have all the prices posted at what I feel is fair, but I will entertain reasonable offers - I'm not the one that needs parts here and it isn't absolutely necessary to sell them so please do not waste my time with ridiculous low ball offers. I will also entertain trades for parts that I need listed on the following thread:
https://www.yotatech.com/forums/f109...wanted-288614/

I will accept payment via PayPal and Shipping will be on your dime, but most parts will fit in a USPS flat rate box. Parts are located in 21804.

Feel free to reply to this thread or PM me with questions. Thanks for looking!

*EGR Cooler/Crossover - $15 - located on the back of the head (Fits 1979-1983 Pickups)
*Water Bypass Pipe - $10 - located on the back on the timing cover on the driver side (Fits 1979-1983 Pickups)
*Thermostatic Vacuum Switching Valve (TVSV) - $15 - located in the on the passenger side of the head between the middle two intake manifold ports (Fits 1981-1983 Pickups)
*Emissions computer - pictured, but no longer available


*Blower motor fan control switch - $10 (Fits 1979-1981 Pickups with the vertical blower motor switch on the heater controls)


*Mechanical fuel pump - $15 (Fits 1979-1983 Pickups)


*Factory clutch master cylinder - $10 - no leaks (Fits 1979-1983 Pickups)


*Factory camshaft - $30 - 132,XXX miles, excellent condition, not abnormal wear, no scarring, no pitting, within factory runout and clearance specs (Fits 1981-1983 Pickups with 22R - not sure about the 20R)



*Factory steering tie rod - $25 - Tie rod ends are still good (Fits 1979-1983 4WD Pickups)



*Factory brake master cylinder - $15 - No leaks (Fits 1979-1983 Pickups)




ITEMS SOLD (no longer available):
*Factory SR5 lower gauge pod - $35
*Factory dash defrost vents - $10
*Factory battery tie down and J-bolt - $15
*Factory gas pedal - $15
*Emissions computer - $15
*Aftermarket front bumper stays - $50
*Aftermarket passenger front bumper turn signal - $30
*Factory visors - $30
*Factory defrost ducts - $20
*Aftermarket corner lenses - $10
*Aftermarket headlight doors - $45 (x2)
*Factory Charcoal canisters - $35
*Factory tag lamps - $30
*Factory door handles - $15
*Aftermarket tail light lenses with chrome trim - $80
*Aftermarket side mirrors - $20
*Factory bucket seats - $165
*Factory Fuel sending unit - $65
*Factory cab louvers/vents - $30
*Factory Rear drum brakes - $60
*Factory Front driveshaft - $50
*Factory hood latch - $15
*Dual row timing chain kit - $60
*Factory cold mixture heater (CMH) - $15
*Factory fuel filler hose - $20
*4WD Fender Emblems - $20
*Factory radiator with cap - $50
*Aftermarket Steering stabilizer - $40
*Factory Ashtray - $15

All items are also selling on eBay - get on them while they are still available!

 

Bump - These parts are selling quick on eBay so get them while you still can!

 

Do you still have the side mirrors?

 

Sure do

 

I sent you a PM.

 

I never received any PMs from you

 

You have a P# for the dual row chain kit?

 

I sent that PM again.

 

Engnbldr Part #TKS904

 

Folks are gobbling these parts up on eBay - I'd rather sell to people in the YT community so speak up if you are interested!

 

Weekly bump

 

PM sent regarding the brake master. Are you positive it's a 15/16? The rearmost casting looks more like a 13/16 to me. Was this truck a 3/4 or full-ton?

 

It is a 13/16 bore from a 1983 4WD. Not what you are looking for?

 

No, not what I'm looking for; too soft for my setup. You replied to my WTB thread for 15/16 (or maybe 7/8).

 

Bump! Some parts still available!

 

Just sold a couple key rare items on eBay today. If you need anything listed you better hop on it. I sell to the first person to send money.

 

Bump - Down to about a dozens parts left...

 

Bump - a few parts still left!

 

shipping on the stabilizer to 97230. Thanks!

 

$10.50