*FS*3.0 stock mani's&crossover, Stock ISR pieces, Taurus fan kit & modded mani's
#1
Registered User
Thread Starter
Join Date: Jul 2003
Location: Dallas, TX
Posts: 221
Likes: 0
Received 0 Likes
on
0 Posts
*FS*3.0 stock mani's&crossover, Stock ISR pieces & modded mani's
Hey all,
All parts are from or for 1994 3.0 4WD 4Runner. I'd like to keep these together in each group as much as possible because I need this stuff gone.
Paypal preferred and all items are located in Richardson, TX. (Dallas)
I have for sale the following:
1) 3.0L stock manifolds (p and d side), stock crossover and heat shields, and welded downpipe. These were removed intact when I had my headers installed. Top end was being rebuilt so no need to cut the stock crossover. downpipe was welded when I had a leak at the flange.
$85 + s&h
2) Stock airbox pieces from when I did my ISR mod. I dont see me needing these so they must go.
$40 + s&h
3) (*SOLD*)Taurus fan install kit.
4) 2 modified passenger side manifolds and stock style manifold gaskets. Has block off ports and allen screw setup for "poor boy" headers. I ended up needing a new HG and just went the Downey header route since they were already all setup. Would make a good setup, just didnt want to fugg with it. Ready for ceramic coating and install. Manifold gaskets included are from the engnbldr kit.
I paid $50 each as stock parts from YotaYard. I'd like to get that back.
$100 + s&h takes it.
First I'll take it in this post gets it.
pm me for payment info. Post Q's here so all can see.
Pics of all items are located here: http://mikegibsonphoto.smugmug.com/g...2120#126477573
cheers everybody,
Mike
All parts are from or for 1994 3.0 4WD 4Runner. I'd like to keep these together in each group as much as possible because I need this stuff gone.
Paypal preferred and all items are located in Richardson, TX. (Dallas)
I have for sale the following:
1) 3.0L stock manifolds (p and d side), stock crossover and heat shields, and welded downpipe. These were removed intact when I had my headers installed. Top end was being rebuilt so no need to cut the stock crossover. downpipe was welded when I had a leak at the flange.
$85 + s&h
2) Stock airbox pieces from when I did my ISR mod. I dont see me needing these so they must go.
$40 + s&h
3) (*SOLD*)Taurus fan install kit.
4) 2 modified passenger side manifolds and stock style manifold gaskets. Has block off ports and allen screw setup for "poor boy" headers. I ended up needing a new HG and just went the Downey header route since they were already all setup. Would make a good setup, just didnt want to fugg with it. Ready for ceramic coating and install. Manifold gaskets included are from the engnbldr kit.
I paid $50 each as stock parts from YotaYard. I'd like to get that back.
$100 + s&h takes it.
First I'll take it in this post gets it.
pm me for payment info. Post Q's here so all can see.
Pics of all items are located here: http://mikegibsonphoto.smugmug.com/g...2120#126477573
cheers everybody,
Mike
Last edited by photomike72; 03-08-2007 at 08:34 AM. Reason: item was sold
#5
Registered User
Thread Starter
Join Date: Jul 2003
Location: Dallas, TX
Posts: 221
Likes: 0
Received 0 Likes
on
0 Posts
I dont see why it wouldnt. The install on 2nd Gens does require trimming on the shroud of the fan, so I dont see why it wouldnt work, but I dont know for sure.
Maybe check in the 1st Gen forum and see if anyone has modded theirs to run this setup.
Cheers,
Mike
Maybe check in the 1st Gen forum and see if anyone has modded theirs to run this setup.
Cheers,
Mike
Trending Topics
#9
Registered User
Thread Starter
Join Date: Jul 2003
Location: Dallas, TX
Posts: 221
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
XtraCab
Solid Axle Swaps, All Years
18
04-12-2020 05:25 AM
FS[SouthEast]: Mercury Villager Fan & DCC Fan Controller
coryc85
Misc Stuff (Vehicle Related)
6
09-09-2015 06:24 AM
GreatLakesGuy
The Classifieds GraveYard
8
09-04-2015 09:27 AM
crashburnoveride
86-95 Trucks & 4Runners
1
07-10-2015 06:39 AM