Post Your Pics!!!
02-06-2010, 04:54 PM
#2621
Registered User
Join Date: Jun 2009
Location: North Carolina
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
this may not be the place to post this, but i need help. how much lift is on this truck. and how hard would it be to keep a driveshaft in
92' Toyota with chevy 350 engine, Holley intake, Edelbrock carb, 700r4 trans, np208 transfer case, dana 44 front, dana 80 rear sitting on 44" Ground Hawgs. Needs rear driveshaft.
92' Toyota with chevy 350 engine, Holley intake, Edelbrock carb, 700r4 trans, np208 transfer case, dana 44 front, dana 80 rear sitting on 44" Ground Hawgs. Needs rear driveshaft.
02-07-2010, 12:22 AM
#2622
Registered User
Join Date: May 2009
Location: Summit, MS
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
i have no idea, what you see above is all i know about the truck. i was thinkin about buyin it, but i wanna how much i'm bout to put in it to get it (and keep it) running. as far as the axles go and the 4x2 conversion, i have no idea
02-07-2010, 04:22 AM
#2625
Registered User
Join Date: Oct 2004
Location: Ringgold Ga/Chattanooga Tn
Posts: 297
Likes: 0
Received 2 Likes
on
2 Posts
this may not be the place to post this, but i need help. how much lift is on this truck. and how hard would it be to keep a driveshaft in
92' Toyota with chevy 350 engine, Holley intake, Edelbrock carb, 700r4 trans, np208 transfer case, dana 44 front, dana 80 rear sitting on 44" Ground Hawgs. Needs rear driveshaft.
92' Toyota with chevy 350 engine, Holley intake, Edelbrock carb, 700r4 trans, np208 transfer case, dana 44 front, dana 80 rear sitting on 44" Ground Hawgs. Needs rear driveshaft.
If that was a serious question just wanted to answer it for you
02-07-2010, 07:30 AM
#2628
Registered User
Join Date: May 2009
Location: Summit, MS
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
yes it was a serious question, thank you. do you happen to know what one may cost?
02-07-2010, 07:41 AM
#2629
Registered User
Join Date: May 2009
Location: Summit, MS
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
02-07-2010, 01:06 PM
#2630
Registered User
Snaped a few cell pics when I got home before it got dark
the 92 getting new bumpers and in the midst of a bed bob:
buddies rigs. the one on the left has a blown 1.6 tracker motor in it its on jeep yj springs in the rear with a custom 3 link up front. sitting on toyota axles and has 6.5 gears in the t case. clears 36s nicley (has 33s on it now) the one on the right has the stock sammy motor (1.3) with toyota axles and jeep yj springs front and rear. sittin on 35' boggers.
the 92 getting new bumpers and in the midst of a bed bob:
buddies rigs. the one on the left has a blown 1.6 tracker motor in it its on jeep yj springs in the rear with a custom 3 link up front. sitting on toyota axles and has 6.5 gears in the t case. clears 36s nicley (has 33s on it now) the one on the right has the stock sammy motor (1.3) with toyota axles and jeep yj springs front and rear. sittin on 35' boggers.
Last edited by rattlewagon; 02-07-2010 at 01:08 PM.
02-07-2010, 02:26 PM
#2631
Registered User
i got bored and went wheelin in the DD and got stuck. hooked a heep up to it that got stuck. the heep had a winch so we we winched the heep out with my truck on a chain connected to the heap. i love a goos little adventure.
When its a Toyota that always a lie..
02-08-2010, 10:55 AM
#2635
Registered User
well its bound to happen sometime. court wasnt too happy tho.
still waiting for bens truck to get out of the garage so i can finish the bed bob. its taken him almost a week to wash and wax it. ill roll it out t his weekend wether hes done or not. cus i wont have any time to work on it for a while. however, i did order my spool today....
02-08-2010, 01:56 PM
#2636
Registered User
Join Date: Oct 2008
Location: Burlington, VT
Posts: 1,584
Likes: 0
Received 0 Likes
on
0 Posts
word, that means that i have no choice but to get a lock rite. I actually hit up bond today to see if i could get one thru them, but they didnt even know what i was talking about until i told them it's kind of like positrac but not as complicated
02-09-2010, 04:54 AM
#2637
Registered User
haha. Bed bob is gonna be a while before it gets finished. Im not going to have any time to do it in the nex couple of weeks. workin every day for a loooong time. but its ok, money for the truck!
can wally from GMC get you a deal on a locker?
can wally from GMC get you a deal on a locker?
02-09-2010, 02:52 PM
#2638
Registered User
Join Date: Oct 2008
Location: Burlington, VT
Posts: 1,584
Likes: 0
Received 0 Likes
on
0 Posts
I'll have to ask him. Thatd be sweet though. Even if he could match say an online price, it would be nice doing business with him rather than a large online company...
02-10-2010, 02:00 AM
#2639
Registered User
Join Date: Dec 2009
Location: Albuquerque, NM
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
I just got my first 4runner. After years of driving toyota gas sippers and Chevy 4x4 gas guzzlers. Here's a couple of pics.
Last edited by Frankie5Fingers; 02-10-2010 at 02:02 AM.
