94 Pickup Rotor Question
#1
Registered User
Thread Starter
Join Date: Jan 2008
Location: Sheridan, AR
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
94 Pickup Rotor Question
I've been reading some of these forum, but I thought it may be quicker just to ask the question. I have a 94 4x4 pickup and I'm thinking of replacing the rotors. It has the factory manual hub and I need to know for sure if I have to removed the hub completely to replace the rotor, or will the rotor slide off of the hub after I remove the pads and caliper. I know there are other post regarding this, but I haven't seen one where someone just wanted to replace the rotor only. Any help would be greatly appreciated.
Thanks
Thanks
#2
Contributing Member
Join Date: Apr 2006
Location: TENN Native Languishing in Virginia
Posts: 4,787
Likes: 0
Received 34 Likes
on
14 Posts
Nope, they are a full-blown PITA. You have to remove the hub completely, and it won't hurt to have an impact wrench. PB Blaster the hell out of the bolts on the rear of the hub & let it sit for a while...
Check the '93 FSM sticky at the top of this forum.
Check the '93 FSM sticky at the top of this forum.
#3
Registered User
Join Date: Jul 2006
Location: Halifax, NS, Canada
Posts: 844
Likes: 0
Received 0 Likes
on
0 Posts
yeah, and getting the rotors off the hub can be a pain in the butt if they're rusted enough. i was convinced they were all one unit until i bashed them hard enough.
i threaded the bolts back into the holes halfway and used a big punch and a really big hammer to beat on them. mangled the threads in one of the holes cause it didn't have enough bite when i threaded it in. i rested the rotor on the backside of one of my wheels which worked well.
soaking it in pb blaster for a few hours is probably a good idea, and if you have access to a press it'll probably be far easier if you can rig up some way to press through the bolt holes (IIRC).
good luck!
i threaded the bolts back into the holes halfway and used a big punch and a really big hammer to beat on them. mangled the threads in one of the holes cause it didn't have enough bite when i threaded it in. i rested the rotor on the backside of one of my wheels which worked well.
soaking it in pb blaster for a few hours is probably a good idea, and if you have access to a press it'll probably be far easier if you can rig up some way to press through the bolt holes (IIRC).
good luck!
Trending Topics
#8
Registered User
Join Date: Feb 2007
Location: CW ohio
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, not so easy. I've got the caliper off, the outer cover 12mm nuts off, but can't firure out how I got past the cone washers in the past. Its a 94 runner 3.0 auto hub BTW.
#9
Contributing Member
Join Date: Apr 2006
Location: TENN Native Languishing in Virginia
Posts: 4,787
Likes: 0
Received 34 Likes
on
14 Posts
NOTE: LEAVE THE LITTLE NUTS ON ABOUT 3-4 TURNS or you'll be finding the washers for the next hour.
1. Using a WOODEN, RUBBER OR PLASTIC MALLET, or a hammer with 2x4 between it and the hub, beat the living hell out of the outer edge next to the washers.
2. Use a brass drift on the end of the bolts & tap with firmly with a hammer directly INTO the bolt.
One of these methods will almost always dislodge the cone washers.
Once you're inside, remove both locking nuts & assorted washers & the bearing. You're there.
#15
Registered User
Join Date: Feb 2007
Location: CW ohio
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
WOOHOO!
Got one after F-in with it all day and buying a $30 2 1/8 socket. I used an old spark plug socket around the cone washers and a BFH.
Tomorrow I'll attack the other side which should go fairly quickly now that I know how. Uh oh, I just screwed the pooch there didn't I?
Oh well, learned a lot today, like I shoulda gotten a better degree so I could pay someone to do these bastards.
Thanks for the advice and thanks to the YotaTech gods for having all of this searchable info. Some of you guys have put alot of work into these write ups and its appreciated.
Got one after F-in with it all day and buying a $30 2 1/8 socket. I used an old spark plug socket around the cone washers and a BFH.
Tomorrow I'll attack the other side which should go fairly quickly now that I know how. Uh oh, I just screwed the pooch there didn't I?
Oh well, learned a lot today, like I shoulda gotten a better degree so I could pay someone to do these bastards.
Thanks for the advice and thanks to the YotaTech gods for having all of this searchable info. Some of you guys have put alot of work into these write ups and its appreciated.
#18
Registered User
Join Date: Jul 2006
Location: Halifax, NS, Canada
Posts: 844
Likes: 0
Received 0 Likes
on
0 Posts
you know, there is a real method for those cone washers - you're supposed to put a tapered punch into the gap and pound it in. it'll expand them and they pop right out. just soak them in pb blaster for a good while beforehand.
#19
Contributing Member
Join Date: Feb 2007
Location: maple ridge, British Columbia, Canada
Posts: 9,055
Likes: 0
Received 9 Likes
on
5 Posts
Am I the only one who didnt have any trouble with my cone washers? Light taps along the side of the hub with a brass hammer while pulling on the hub worked like a charm.
#20
Contributing Member
Join Date: May 2004
Location: marlbank, canada
Posts: 2,839
Likes: 0
Received 0 Likes
on
0 Posts
i used to do the hammer thing, then i went to a fine tipped flat screwdriver inserted into the slot of the cone washer. a light tap with a hammer and they come right out, usually gripping the screwdriver blade.
a punch applied directly to the end of the studs will dislodge them as well. remember, a bit of antisieze and finesse will go a long way.
lee
a punch applied directly to the end of the studs will dislodge them as well. remember, a bit of antisieze and finesse will go a long way.
lee