92 TOY's 22re / crapped out / gotta start somewhere / thread
#681
YotaTech Milestone-Two Millionth Post
Thread Starter
Your gonna regret dropping that Diff, I did, as for the oil pan gasket, if you were to take the bolts out, the pan drops enough to get the gasket off and place a new one on. The cross member is also a PITA to get back in. and if not lined up properly, can affect alignment.
I'f I come down there. I'll have that thing out in less than 20 minutes
I'f I come down there. I'll have that thing out in less than 20 minutes
I know I'm getting flamed for being obsessive about this, but that's OK with me.
still reading.............
#682
YotaTech Milestone-Two Millionth Post
Thread Starter
OK.
Looks like I could remove this bolt rather easily....
These are the motor mounts? Right?.......Not touching, just asking.
Why does it look like this stuff will get crushed if I raise the engine?? I now I'm only supposed to raise it less than an inch as per the FSM, but........
Looks like I could remove this bolt rather easily....
These are the motor mounts? Right?.......Not touching, just asking.
Why does it look like this stuff will get crushed if I raise the engine?? I now I'm only supposed to raise it less than an inch as per the FSM, but........
#683
YotaTech Milestone-Two Millionth Post
Thread Starter
xxxtreme22r...
I can't see how raising it an inch is going to provide me clearance to do anything....and by the looks of it I have just barely more than an inch to raise it.
I can't see how raising it an inch is going to provide me clearance to do anything....and by the looks of it I have just barely more than an inch to raise it.
#684
YotaTech Milestone-Two Millionth Post
Thread Starter
when I jack up the truck, should I put jack stands under the frame at about the leading edge of the doors or where should I put them???
#685
Registered User
You have an auto so there are more wires heading to the tranny than us with the 5spd.
1. Take all the bolts out
2. Unbolt the oil pickup (worry about getting it in later) let it drop in the pan
3. Wiggle it out/attempt to wiggle it out
4. See what it's catching on and remove it/slide it/cut it/persuade it
5. Cuss, swear, cleanup the cuts, tell the wife it's alright and I'll be in shortly (knowing that you will not be)
6. Lift motor and loosen diff mount
7. Wonder why you didn't do that in the first place
8. Come back on here with pictures and a writeup on your latest experence.
Easier than the 10 steps for AA mine only has 8
1. Take all the bolts out
2. Unbolt the oil pickup (worry about getting it in later) let it drop in the pan
3. Wiggle it out/attempt to wiggle it out
4. See what it's catching on and remove it/slide it/cut it/persuade it
5. Cuss, swear, cleanup the cuts, tell the wife it's alright and I'll be in shortly (knowing that you will not be)
6. Lift motor and loosen diff mount
7. Wonder why you didn't do that in the first place
8. Come back on here with pictures and a writeup on your latest experence.
Easier than the 10 steps for AA mine only has 8
#687
Registered User
Take your front tires off as well so that the truck isn't as high when you get the stands under there.
#689
YotaTech Milestone-Two Millionth Post
Thread Starter
You have an auto so there are more wires heading to the tranny than us with the 5spd.
1. Take all the bolts out
2. Unbolt the oil pickup (worry about getting it in later) let it drop in the pan
3. Wiggle it out/attempt to wiggle it out
4. See what it's catching on and remove it/slide it/cut it/persuade it
5. Cuss, swear, cleanup the cuts, tell the wife it's alright and I'll be in shortly (knowing that you will not be)
6. Lift motor and loosen diff mount
7. Wonder why you didn't do that in the first place
8. Come back on here with pictures and a writeup on your latest experence.
Easier than the 10 steps for AA mine only has 8
1. Take all the bolts out
2. Unbolt the oil pickup (worry about getting it in later) let it drop in the pan
3. Wiggle it out/attempt to wiggle it out
4. See what it's catching on and remove it/slide it/cut it/persuade it
5. Cuss, swear, cleanup the cuts, tell the wife it's alright and I'll be in shortly (knowing that you will not be)
6. Lift motor and loosen diff mount
7. Wonder why you didn't do that in the first place
8. Come back on here with pictures and a writeup on your latest experence.
Easier than the 10 steps for AA mine only has 8
UMMMM...12 steps for AA
Yeah, sitting here waiting for the Doctor to call......so I'm in and out.
#690
Registered User
#691
YotaTech Milestone-Two Millionth Post
Thread Starter
I'm gonna just let that one go...............
Anyway......probably gonna run to SEARS....$24.99....can't really do much with having something like these......they go up to 21''..............so moreroom for me.....I'm in no way heavy but I like to not have heavy metal stuff right against my head.
#693
YotaTech Milestone-Two Millionth Post
Thread Starter
#695
YotaTech Milestone-Two Millionth Post
Thread Starter
#696
Registered User
make sure you got a pry par set, you gonna need it to get that diff back in. especially the front mount. I didnt realize those wires were there, since you do have an auto, I got the 5sp. Maybe thats why some of us had to drop the diff and some of us hasn't.
#697
YotaTech Milestone-Two Millionth Post
Thread Starter
I'm assuming I shouldn't do anything without the jackstands.
The automatic trans is a concern in this always.......I have fluid lines running where you guys don't......that was one thing I listed as a concern.....I know with so many posts it gets lost......but i remember it all.......that's why there's so much preparation for me. I want ALL the knowledge 1st....then I will wrench.
I thoroughly appreciate everyone's input.
#699
Registered User
those motor mount bolts you circled are the wrong ones, yes those are the motor mounts, however you want to undo the two on each side that bolt the mount to the frame. If I remember right they are 14mm.