92 TOY's 22re / crapped out / gotta start somewhere / thread
#2401
YotaTech Milestone-Two Millionth Post
Thread Starter
NOTE>
use ear protection when using the BOOTY FAB.....my ears are still ringing about an hour later....no bueno.
use ear protection when using the BOOTY FAB.....my ears are still ringing about an hour later....no bueno.
#2403
YotaTech Milestone-Two Millionth Post
Thread Starter
ok, so i was seeing if i could send a video from my phone, to youtube and then post it up...and it worked....i took it down, because it was video of our cat looking around....
#2407
YotaTech Milestone-Two Millionth Post
Thread Starter
hahaha
was out there looking....looks like all the electrical connections / sensors are as they should be....want to get a better look from in the passenger's wheelwell though....then i will bolt up the lower intake...probably later today...then fart around with the injectors.
#2411
#2412
YotaTech Milestone-Two Millionth Post
Thread Starter
#2415
YotaTech Milestone-Two Millionth Post
Thread Starter
this is one of the plugs that i did not remember plugging back in and i could not see it from above.....so i peeked through the side and there it was. i remembered ROGERMAN also missing this and i can understand why. it is hidden pretty well.
had to plug and unplug a few times to be sure i had it right because i was doing it blindly and by feel.
so then i cleaned up the mating surfaces for the lower intake.....scraper and the acetone.
i think i'm ready to bolt this on........objections??
had to plug and unplug a few times to be sure i had it right because i was doing it blindly and by feel.
so then i cleaned up the mating surfaces for the lower intake.....scraper and the acetone.
i think i'm ready to bolt this on........objections??
#2417
YotaTech Milestone-Two Millionth Post
Thread Starter
PROBLEM
well kinda.
when i put the EGR valve back on like i was supposed to, (page EM30 of the FSM for you playing along at home)....it said to put it on....not wait until the intake gasket was on. the gasket i have is meant to be put on BEFORE the EGR.......no biggie to me, i did use RTV there so i am just going to trim that part off and away.
well kinda.
when i put the EGR valve back on like i was supposed to, (page EM30 of the FSM for you playing along at home)....it said to put it on....not wait until the intake gasket was on. the gasket i have is meant to be put on BEFORE the EGR.......no biggie to me, i did use RTV there so i am just going to trim that part off and away.
#2418
Registered User
FWIW, I would pull the EGR back off & put it on with the intake gasket. The exhaust gases circulating thru the EGR are very hot & I am not sure that the RTV will hold up very long. Just use the gasket dry. Also take my advise as you will but not as the last word. I put my intake & EGR on with a dry gasket & have no problem so far.
#2419
YotaTech Milestone-Two Millionth Post
Thread Starter
FWIW, I would pull the EGR back off & put it on with the intake gasket. The exhaust gases circulating thru the EGR are very hot & I am not sure that the RTV will hold up very long. Just use the gasket dry. Also take my advise as you will but not as the last word. I put my intake & EGR on with a dry gasket & have no problem so far.
following the FSM...that's the funny part.....grrrrr
#2420
YotaTech Milestone-Two Millionth Post
Thread Starter
OK it's on (the lower part)...not torqued but this little coolant pipe is kicking my ass.
can't get one screw to thread.
can't get one screw to thread.